Software Update Name: BCM.R400.273-UTPS

Applicable H/W Platforms: BCM1000, BCM200, BCM400, SRG200 1.5, SRG400 1.5

Applicable S/W Platforms: BCM 4.0, SRG 1.5 based on BCM 4.0

Category: GEN 

Installation Recommendations:
This update should be applied to all new installs of BCM 4.0 and SRG 1.5 based 
on BCM 4.0. Existing installations should have this update applied if they are 
experiencing any of the issues that are corrected. There is no need to schedule
specific maintenance to apply this upgrade if there are no reported issues.
In those cases, systems should be updated at the next regular service opportunity. 

Components and Versions:
 
   utps 41.340.2.12
   ipsetfirmware 41.4.05.0

Dependencies: 
   Required Updates:
   - BCM.R400.248-CORE-UTPS or later
   OR
   - BCM.R400.SU.System.018.200901 or later

   Updates should be applied in the following order:
   - BCM.R400.248-CORE-UTPS or BCM.R400.SU.System.018.200901
   - BCM.R400.273-UTPS

   Product Dependencies: None 

Size: 15MB

System Impact: 
Time to apply approximately 20 minutes

Does update application force reboot: Yes

Other Impacts: None

Limitations: None

Update Removable: No

Description:
------------
The following issues are addressed:

1. Last "L" of the "NEWCALL" softkey is shifted to the next key while using three way conference call
   Support has been added so that all the softkey labels which are displayed
   on 1110, 1120, 1140 IPSets are in lower case except for the first character.
   Q01930775-03


This update includes the content of the following superseded updates: 

BCM.R400.203-UTPS
-----------------

1. The LCD on the KEM modules going blank intermittently
   The following latest firmware is being included in the BCM 4.0 build which 
   fixes the 1110 series expansion module's issues.
   0623C4L.bin - for 1110 (Next Gen) IP Phone
   0624C4L.bin - for 1120 (Next Gen) IP Phone
   0625C4L.bin - for 1140 (Next Gen) IP Phone
   Q01877250

BCM.R400.191-UTPS
-----------------

1. Single IP Phone locks up after reboot
   Due to a port mismatch the DN of the IP set gets assigned to Co-loop.
   During restart of an IP set, UTPS was using LAD and STNX information 
   received from Core through the "query PDN Response" FUMP without 
   checking for hardware ID and Set Type. This is now fixed by verifying 
   the hardware ID and the Set type in the FUMP message.
   This is validated against the expected Hardware ID and the Set type. 
   Q01801665

BCM.R400.168-UTPS
-----------------

1. Issues found during Designer Testing of the Expansion Module for 
   IP Phone 1100 series Hardware.
   Issues were found while testing with the Expansion Module for 
   IP Phone 1100 series hardware. There was a mismatch in the Expansion 
   Module for IP Phone 1100 series type. Also, issues with the misalignment
   of the KEM labels are fixed. 
   Expansion Module for IP Phone 1100 series is now supported with BCM4.0
   Q01578700-03

2. Support for IP Phone 1110 Sets in BCM4.0
   A new firmware file was added in the BCM4.0 build to support IP Phone 1110.
   Q01764255

3. Inclusion of new firmware files for 1110, 1120e, 1140e, 2007, 
   2002 and 2004 Phase 2 IP sets.
   Added the latest versions of firmware files for 1110 (0623C4D),
   1120e(0624C3G), 1140e(0625C3G), 2007(0621C3N), 2002 and 2004
   Phase 2 Sets (0604DAX). LLDP is supported on 0604DAX.
   Q01779467

BCM.R400.125-UTPS
-----------------

1. Spoofed Brute-Force UNISTIM message attack puts IP set in surveillance mode.
   This vulnerability is removed by using 30 bits for the initial reliable 
   UDP sequence number seeding, and good randomization in the phone
   and the BCM.
   Q01693925-02

2. Spoofed UNISTIM reauthentication messages cause Denial-of-Service to 
   IP Clients
   When there is an illegitimate request coming in from an unknown/fake 
   (spoofed) set which has the same IP address as that of an IP set which has 
   already booted up and is running, we send a NACK with the 
   NextRxSequenceNumber. This will ensure that there is no disruption to the
   connection of the legitimate IP set.
   Q01693840-02

BCM.R400.097-UTPS
-----------------

1. UTPS crash when an IP set attached to a KEM module resets.
   When an IP set attached to a KEM module with line appearances is reset due 
   to loss of power, or is rebooted, the UTPS service will stop functioning. 
   This will cause all IP sets connected to the BCM to go down. A reboot of 
   the BCM is required to restore UTPS service. 
   UTPS was fixed to handle this situation without crashing.
   Q01546584-02 

BCM.R400.033-SMG
----------------

1. Delayed Paging 
   The first part of a page can be cut off on some IP sets when a large number 
   of IP sets is paged at the same time. This is due to delayed VoIP paging
   setup. The fix included in this patch will reduce the paging setup time 
   for IP sets to enable paging to a greater number of IP sets than would 
   be practical without this patch.
   Q01224647, Q01301100

2. Missing voice path for call answer via off-hook handset when hotdesking
   When a desktop phone (e.g. 2004) is used to 'Hot Desk' a softphone 
   (e.g. 2050), that Handsfree and Headset modes on the desktop phone became 
   unusable. With this fix, a user using a desktop phone to Hot Desk a 
   softphone will be able to make use of the Handsfree and Headset 
   capabilities of the desktop phone when making or receiving calls.
   Q01416055-01

3. Infrequent no-way speech path call when using IP phone 
   Every time an IP phone made or received a call there was a very small 
   probability that this call would not have audio (user does not hear
   and is not heard by far-end). This fix resolves the issue. 
   Q01404093

4 Listening R metric is reported against desktop clients for i2050 
   P2 softphones
   When 2050 softphones detect PVQM violations, these violations are reported 
   against 'desktop phones' in the PVQM management panel of Element Manager 
   when they should have been reported against 'softphone'. 
   This fix resolves the issue. 
   Q01327461-01

5. PVQM Alarm description as mentioned in the FD is not shown in EM
   When PVQM violations are detected, an alarm is raised. This fix enhances
   the PVQM information carried in the text of the alarm to allow tools such as
   Net6 servers to perform advanced processing on the PVQM data. 
   Q01410941-01

6. Alarm 50503 generated when called from an i2050 set
   Sometimes the 2050v2 softphone generated PVQM alarms reporting 0% packet 
   loss in error. This fix eliminates these erroneous alarms. 
   Q01407702

7. On i2004 set, need to hold button down to see what is programmed on to it.
   When entering the button inquiry feature via 'Feature*0' to query key
   programming information, sometimes IP phones would only display the key 
   programming information for a very brief period of time making it 
   hard to read. This fix addresses the issue
   Q01357516-02

8. IP Set's DN not retained during upgrade
   When upgrading from a BCM3.x to BCM4.0, some IP phones may lose their
   DN programming as a result therefore requiring the need to reprogram
   the DN on the phone. This fix addresses the issue. 
   Q01449571

