Software Update Name: BCM.R400.346-UTPS

Applicable H/W Platforms: BCM1000, BCM200, BCM400

Applicable S/W Platforms: BCM 4.0

Category: GEN

Installation Recommendations:
This update should be applied to all new installs of BCM 4.0 
systems. Existing installations should have this update applied
if the CR condition is noticed. There is no need to 
schedule specific maintenance to apply this upgrade if there 
are no reported issues. In those cases, systems should be 
updated at the next regular service opportunity. 

Components and Versions:
 
   utps 41.410.0.12
   ipsetfirmware 41.5.1.3
   iptelephony 41.90.2.70


Dependencies: 
	Required Updates:  
 	 - BCM.R400.SU.System.029-201012 or later

Updates should be applied in the following order:
  	 - BCM.R400.SU.System.029-201012 or later
	 - BCM.R400.346-UTPS

Product Dependencies: None

Size: 19.76 MB

System Impact: 
Time to apply approximately 20 minutes

Does update application force reboot: Yes

Other Impacts: None

Limitations: None

Update Removable: No

Description:
------------
The following issues are addressed:

1. The first few seconds of conversation is muted for calls to IP sets.
   When calling 12xx IP set, the called party speech is muted
   for the first 0.5-1.5 seconds due to delayed acknowledgement from
   12xx set to BCM for setting of speech path.
   
   Inclusion of UNIStim 5.1 solves this issue.
   0621C8D,0623C8D,0624C8D and 0625C8D for IP phones i2007, 1110, 1120e 
   and 1140e respectively. 
   wi00894449

This update includes the content of the following superseded updates:

BCM.R400.332-UTPS-2.3-1.0
-------------------------
1.Bad volume control of ring tone since UNIStim 3.3.
Inclusion of UNIStim4.2 for IP Set solves the issue.
Firmware 0623C7M/0624C7M/0625C7M for IP phones 
1110/1120E/1140E respectively.
Q02142594
 

BCM.R400.326-UTPS-2.2-1.0
--------------------------
1.Inclusion of UniStim3.4 firmware 0604DCN for 
i2001/i2002/i2004 Phase II - IP phones
Inclusion of UniStim4.1 firmware 0623C7J/0624C7J/0625C7J/0621C7D for 
IP phones 1110/1120E/1140E/2007 respectively
Q02124398 - 03

BCM.R400.298-UTPS-2.1-1.0
-------------------------
1. i2007 volume fluctuates during calls when using headset 0621C4V 
The issue is with Echo cancellation within the firmware, as it should not lower 
the volume but cut down background noise.

Inclusion of UNIStim3.3 firmware for IP set solves the issue.
0604DCL for Phase II IP Phones (2001, 2002 & 2004).
0621C6P for IP Phone 2007.
0623C6R, 0624C6R, 0625C6R for IP Phone 1110e, 1120e and 1140e respectively.
Q01988838-01

BCM.R400.282-UTPS
-----------------

1.The ring tone is loud on the 2nd call to 1120e and 1140e Sets
The ring tone on second calls to 1140e and 1120e sets is softer when 
connected to CS1K, but with the BCM, the ring tone is loud and disruptive.
This was the result of older version of IP set firmware.

Inclusion of the UNIStim Firmware Release 3.2 for IP Phones resolves the issue:
0604DCJ for Phase II IP Phones (2001, 2002 & 2004).
0621C6M for IP Phone 2007.
0623C6O, 0624C6O, 0625C6O for IP Phone 1110, 1120E and 1140E respectively.
Q01914009

2. IP Phone can't receive or make calls after BCM is rebooted 
Due to a port mismatch the DN of the IP set gets assigned to Co-loop.
During restart of an IP set, UTPS was using LAD and STNX information 
received from Core through the "query PDN Response" FUMP without 
checking for hardware ID and Set Type. This issue is resolved by verifying 
the hardware ID and the Set type in the FUMP message.
The validation is done against the expected Hardware ID and the Set type.
Q02008973

BCM.R400.273-UTPS
-----------------

1. Last "L" of the "NEWCALL" softkey is shifted to the next key while using 
three way conference call
Support has been added so that all the softkey labels which are displayed
on 1110, 1120, 1140 IPSets are in lower case except for the first character.
Q01930775-03

BCM.R400.203-UTPS
-----------------

1. The LCD on the KEM modules going blank intermittently
The following latest firmware is being included in the BCM 4.0 build which 
fixes the 1110 series expansion module's issues.
0623C4L.bin - for 1110 (Next Gen) IP Phone
0624C4L.bin - for 1120 (Next Gen) IP Phone
0625C4L.bin - for 1140 (Next Gen) IP Phone
Q01877250

BCM.R400.191-UTPS
-----------------

1. Single IP Phone locks up after reboot
Due to a port mismatch, the DN of the IP set gets assigned to Co-loop.
During restart of an IP set, UTPS was using LAD and STNX information 
received from Core through the "query PDN Response" FUMP without 
checking for hardware ID and Set Type. This is now fixed by verifying 
the hardware ID and the Set type in the FUMP message.
This is validated against the expected Hardware ID and the Set type. 
Q01801665

BCM.R400.168-UTPS
-----------------

1. Issues found during Designer Testing of the Expansion Module for 
IP Phone 1100 series Hardware.
Issues were found while testing with the Expansion Module for 
IP Phone 1100 series hardware. There was a mismatch in the Expansion 
Module for IP Phone 1100 series type. Also, issues with the misalignment
of the KEM labels are fixed. 
Expansion Module for IP Phone 1100 series is now supported with BCM4.0
Q01578700-03

2. Support for IP Phone 1110 Sets in BCM4.0
A new firmware file was added in the BCM4.0 build to support IP Phone 1110.
Q01764255

3. Inclusion of new firmware files for 1110, 1120e, 1140e, 2007, 
2002 and 2004 Phase 2 IP sets.
Added the latest versions of firmware files for 1110 (0623C4D),
1120e(0624C3G), 1140e(0625C3G), 2007(0621C3N), 2002 and 2004
Phase 2 Sets (0604DAX). LLDP is supported on 0604DAX.
Q01779467

BCM.R400.125-UTPS
-----------------

1. Spoofed Brute-Force UNISTIM message attack puts IP set in surveillance mode.
This vulnerability is removed by using 30 bits for the initial reliable 
UDP sequence number seeding, and good randomization in the phone
and the BCM.
Q01693925-02

2. Spoofed UNISTIM reauthentication messages cause Denial-of-Service to 
IP Clients
When there is an illegitimate request coming in from an unknown/fake 
(spoofed) set which has the same IP address as that of an IP set which has 
already booted up and is running, we send a NACK with the 
NextRxSequenceNumber. This will ensure that there is no disruption to the
connection of the legitimate IP set.
Q01693840-02

BCM.R400.097-UTPS
-----------------

1. UTPS crash when an IP set attached to a KEM module resets.
When an IP set attached to a KEM module with line appearances is reset due 
to loss of power, or is rebooted, the UTPS service will stop functioning. 
This will cause all IP sets connected to the BCM to go down. A reboot of 
the BCM is required to restore UTPS service. 
UTPS was fixed to handle this situation without crashing.
Q01546584-02 

BCM.R400.033-SMG
----------------

1. Delayed Paging 
The first part of a page can be cut off on some IP sets when a large number 
of IP sets is paged at the same time. This is due to delayed VoIP paging
setup. The fix included in this patch will reduce the paging setup time 
for IP sets to enable paging to a greater number of IP sets than would 
be practical without this patch.
Q01224647, Q01301100

2. Missing voice path for call answer via off-hook handset when hotdesking
When a desktop phone (e.g. 2004) is used to 'Hot Desk' a softphone 
(e.g. 2050), that Handsfree and Headset modes on the desktop phone became 
unusable. With this fix, a user using a desktop phone to Hot Desk a 
softphone will be able to make use of the Handsfree and Headset 
capabilities of the desktop phone when making or receiving calls.
Q01416055-01

3. Infrequent no-way speech path call when using IP phone 
Every time an IP phone made or received a call there was a very small 
probability that this call would not have audio (user does not hear
and is not heard by far-end). This fix resolves the issue. 
Q01404093

4. Listening R metric is reported against desktop clients for i2050 
P2 softphones
When 2050 softphones detect PVQM violations, these violations are reported 
against 'desktop phones' in the PVQM management panel of Element Manager 
when they should have been reported against 'softphone'. 
This fix resolves the issue. 
Q01327461-01

5. PVQM Alarm description as mentioned in the FD is not shown in EM
When PVQM violations are detected, an alarm is raised. This fix enhances
the PVQM information carried in the text of the alarm to allow tools such as
Net6 servers to perform advanced processing on the PVQM data. 
Q01410941-01

6. Alarm 50503 generated when called from an i2050 set
Sometimes the 2050v2 softphone generated PVQM alarms reporting 0% packet 
loss in error. This fix eliminates these erroneous alarms. 
Q01407702

7. On i2004 set, need to hold button down to see what is programmed on to it.
When entering the button inquiry feature via 'Feature*0' to query key
programming information, sometimes IP phones would only display the key 
programming information for a very brief period of time making it 
hard to read. This fix addresses the issue
Q01357516-02

8. IP Set's DN not retained during upgrade
When upgrading from a BCM3.x to BCM4.0, some IP phones may lose their
DN programming as a result therefore requiring the need to reprogram
the DN on the phone. This fix addresses the issue. 
Q01449571

<html>
    <head>
        <title>Runtime Error</title>
        <style>
         body {font-family:"Verdana";font-weight:normal;font-size: .7em;color:black;} 
         p {font-family:"Verdana";font-weight:normal;color:black;margin-top: -5px}
         b {font-family:"Verdana";font-weight:bold;color:black;margin-top: -5px}
         H1 { font-family:"Verdana";font-weight:normal;font-size:18pt;color:red }
         H2 { font-family:"Verdana";font-weight:normal;font-size:14pt;color:maroon }
         pre {font-family:"Lucida Console";font-size: .9em}
         .marker {font-weight: bold; color: black;text-decoration: none;}
         .version {color: gray;}
         .error {margin-bottom: 10px;}
         .expandable { text-decoration:underline; font-weight:bold; color:navy; cursor:hand; }
        </style>
    </head>

    <body bgcolor="white">

            <span><H1>Server Error in '/' Application.<hr width=100% size=1 color=silver></H1>

            <h2> <i>Runtime Error</i> </h2></span>

            <font face="Arial, Helvetica, Geneva, SunSans-Regular, sans-serif ">

            <b> Description: </b>An application error occurred on the server. The current custom error settings for this application prevent the details of the application error from being viewed remotely (for security reasons). It could, however, be viewed by browsers running on the local server machine.
            <br><br>

            <b>Details:</b> To enable the details of this specific error message to be viewable on remote machines, please create a &lt;customErrors&gt; tag within a &quot;web.config&quot; configuration file located in the root directory of the current web application. This &lt;customErrors&gt; tag should then have its &quot;mode&quot; attribute set to &quot;Off&quot;.<br><br>

            <table width=100% bgcolor="#ffffcc">
               <tr>
                  <td>
                      <code><pre>

&lt;!-- Web.Config Configuration File --&gt;

&lt;configuration&gt;
    &lt;system.web&gt;
        &lt;customErrors mode=&quot;Off&quot;/&gt;
    &lt;/system.web&gt;
&lt;/configuration&gt;</pre></code>

                  </td>
               </tr>
            </table>

            <br>

            <b>Notes:</b> The current error page you are seeing can be replaced by a custom error page by modifying the &quot;defaultRedirect&quot; attribute of the application's &lt;customErrors&gt; configuration tag to point to a custom error page URL.<br><br>

            <table width=100% bgcolor="#ffffcc">
               <tr>
                  <td>
                      <code><pre>

&lt;!-- Web.Config Configuration File --&gt;

&lt;configuration&gt;
    &lt;system.web&gt;
        &lt;customErrors mode=&quot;RemoteOnly&quot; defaultRedirect=&quot;mycustompage.htm&quot;/&gt;
    &lt;/system.web&gt;
&lt;/configuration&gt;</pre></code>

                  </td>
               </tr>
            </table>

            <br>

    </body>
</html>
