Software Update Name: BCM050.R300.CORE-TELEPHONY-105

Applicable H/W Platforms: BCM50, BCM50a, BCM50e, BCM50b, BCM50ba, BCM50be, SRG50

Applicable S/W Platforms:  6.0.2.05, SRG50 R3

Category: GEN

Installation Recommendations: 
This update should be applied to all new installs of BCM50 R3 and SRG50 3.0. 
Existing installations should have this update applied if they are experiencing any 
of the issues that are corrected. There is no need to schedule specific maintenance 
to apply this upgrade if there are no reported issues. In those cases, systems
should be updated at the next regular service opportunity.

Component & Version: 
   core-telephonyi	1.2.44.2.18.17
   (Internal Software version code: 30DwC18)
                 
Dependencies:
   Required Updates:
   BCM050.R300.SU.System-89.200808 or later 
   (NOTE: BCM050.R300.SU.System-89 has dependency on BCM050.R300.SU.Desktop-54.200804 or later)
   BCM050.R300.DSP-FIRMWARE-85 or later

Updates should be applied in the following order:
   BCM050.R300.SU.Desktop-54.200804
   BCM050.R300.SU.System-89.200808
   BCM050.R300.DSP-FIRMWARE-85
   BCM050.R300.CORE-TELEPHONY-105

Product Dependencies: None

Size: 3.8MB

System Impact: 
   Time to apply approximately 10 min

   Does update application force reboot: Yes

   Other Impacts: 
   Installation of the update will cause all telephony services to cease during
   this time. The services will restart automatically after the update installs.

Limitations: None

Update Removable: No

Description:
------------
The following issues are addressed:

1. Remote MWI from CO not lighting the message waiting lamp on BCM sets.
   When an incoming call is forwarded to the Central Office voice mail, the 
   message waiting indicator is not lit on the called BCM set after the message 
   has been left.  
   Q01894588


This update includes the content of the following superseded updates:

BCM050.R300.CORE-TELEPHONY-95
-------------------------------

1. F**SYSID produces incorrect value
   From SBA, when user dial F**SYSID, it reproduces wrong system ID.
   Q01891994

2.  **OPTION for GATM2 works only after 2 Reboots instead of 1 as per the Design
   Disconnect Supervision Tone settings that are configurable under
   GATM2 parameters in **OPTION are not getting reflected with the 
   first power reboot of BCM50. It is getting reflected in the second 
   power reboot instead.
   Q01890165 

3. PRI doesn't come back into service after remote alarm
   When there is a short interruption of the PRI service that results
   in a remote alarm (AIS, RAI), then the DTM Module in the BCM shows
   a remote alarm (yellow led in the upper left corner is lit) as expected.
   However, when the PRI service is re-established, the DTM Module still
   shows a remote alarm and no incoming or outgoing calls are possible.
   Remote alarm condition should be cleared on the DTM Module.
   Q01822428-01

4. Calls with NO CLID cannot connect to BCM50 via H323
   When incoming call from PSTN gets tandem out over the VoIP with private route,
   call gets dropped.
   Q01883856-01

BCM050.R300.CORE-TELEPHONY-84
-------------------------------
1. Post-GA-GATI/GATM for Italy Profile 
   Support is added for GATI and GATM for the Italy market profile.
   Q01821379-02

2. CLID through GATM8 is broken
   CLID is not working on GATM trunks in UK profile. 
   The solution for this issue applies to both GATM-Ver1 and
   GATM-Ver2 hardware. This problem is not present for GATI trunks.
   Q01884757

3. Analog trunk locks up while parking
   Analog trunks lock up while using the call park feature.
   Line status shows "line in use."
   Q01860285, Q01876848, Q01884884

4. The intercom keys on the IP phone in the hunt group get locked up
   Call comes to BCM50R3 over a BRI trunk, call gets answered by the set 
   A and transfers the call to HG01. HG members sets 
   B, C and D ring. Once Set B answers the call, the intercom key of 
   sets C and D remain lit and the sets C and D are locked up.
   Q01870745

5. Tandem Call from PSTN rings at the control set
   All tandem calls from the PSTN to the remote site ring 
   at the control set instead of correct extension number.
   Q01822669-05

6. Partial loss of Telephony Programming post Power cut
   Loss of recently configured core telephony data may occur following a 
   coretel restart.
   Q01685795-03

7. Outgoing CLID is incorrect for ISDN DNs
   After applying patch BCM.R400.SU.System.004.2007 the outgoing CLID information 
   is incorrect. Sets no longer use the assigned OLI, but instead they use OLIs from the
   inactive DNs.
   Q01808203-04

8. Coretel crashes when TRO is used.
   Problem
   - Place an established internal call on hold
   - Seize a VoIP line and dial a set on a destination BCM
   - Conference the VoIP line with the held call before the destination set answers
   - The destination set is CFAC back to another set on the originating BCM. Trunk Route 
     Optimization is invoked.
   - Any further action taken by the conference master results in a coretel crash
   Q01818223-02

9. Calls using the SIP Trunks not reverting to the Prime Set when WAN Link fails
   Calls that route across the Virtual Trunk using SIP, are not being redirected to the 
   Prime Set when the WLAN link is down.
   Q01833351-01

BCM050.R300.CORE-TELEPHONY-56
-----------------------------

1. Call Collision for Australia Profile.
   Call collision feature is an Australian regulatory requirement. 
   For unsupervised and ROA trunks, an outgoing call is not allowed 
   within 10 seconds of receiving the incoming call. This feature is implemented 
   in this update for GATI and GATM-Ver2.
   Q01745162-01
   Q01754458-01 

2. Stations Globalization for Spain Market Profile.   
   Support is added for GASM and GASI for Spain profile.
   Q01836357-01
   Q01684879-06

3. Adding new Disconnect OSI Timer value in New Zealand Market Profile.
   Added 800, 900, 1000 and 1100 Disconnect OSI timer values for 
   NZ market profile.
   Q01724774-02

4. Trunk Globalization for Saudi Market profile. 
   Support is added for GATM-Ver2 and GATI for Saudi Market Profile.
   Q01586579-01

5. Expensive Route message not displaying on overflow.
   When the VoIP trunk circuit is disconnected or fails,
   "Expensive Route" message is not displayed on the telset 
   when the call is routed over the fallback.
   Q01840161

6. Tandem call forwarding using IP trunks unsuccessful for cell phone numbers.
   An outside caller calls in on a PRI to site "A" and is tandemed to site "B" over VoIP. 
   When the destination set at site B is CFAC to a cell phone in the PSTN, the
   resulting call does not go through.  
   Q01821801

7. Hunt group metrics not working
   An external incoming call is answered by Auto Attendant and then
   transferred to Hunt Group. If the call is abandoned before the Hunt
   Group member answers, the Hunt Group metric for abandoned calls can
   be incorrectly decremented. This can result in large negative numbers in 
   the abandoned call metric. 
   Q01825303-02

8. BCM calling CS1000 via SPS is Blocked if SIGO=ESN5 on Route
   Register the BCM as a SIP Endpoint on the SPS. Add routing
   on the BCM to allow connection to a CS1000 system in the
   network. On the SIP route of the CS1000 have SIGO set to
   ESN5. Make a call from the BCM set to the CS1000 Set.
   The call will fail if the SIGO in the CS1000 is set to ESN5.
   Q01815787

9. UK market: CLID is presented after call answer rather than while ringing
   When a set is configured in 'Cap's n Pref's' to First Display 'Line', and the CLID 
   is withheld on an incoming call the line number only shows up after answering
   the call, instead of while the call is ringing.  
   Q01801594-03

BCM050.R300.CORE-TELEPHONY-33
-----------------------------

1. Analog Trunk Globalization for Singapore
GATM-Ver2 and GATI Analog Trunk support is
added for Singapore profile in this update.
Q01658729-01

2. Analog Trunk Globalization for Malaysia
GATM-Ver2 and GATI Analog Trunk support is
added for Malaysia profile in this update.
Q01605492-01

3. Supervised ROI trunks drop when AA answers in Australia
Incoming calls are getting dropped when answered for ROI supervised mode 
in the Australia profile. This is an intermittent issue. This issue is 
addressed for GATM-Ver1 and GATM-Ver2 firmware in this update.
Q01663473-03
Q01470485-03

4. GATM4 failure during Soft Reset
Intermittently, the GATM-Ver2 hardware will not recover after a soft reset. 
A soft reset includes any of the following actions:
* Disable/Enable,
* Change of Line Tuning Digit,
* Change of Trunk Mode
* Change of Market Profile
This problem did not occur with old GATM-Ver1 hardware.
This issue is addressed in this update.
Q01679650-01

5. Echo on analog DID trunks (ADID4)
Echo can be heard during the first 10 seconds of a call for analog DID 
trunks on some Central Office exchanges. This issue is addressed in this
update.
Q01760892-01

6. Lack of Call timer in a priority call
Whenever there is a priority call, UTPS does not receive the "SET CALL 
TIMER ACTIVE" stim from the CoreTel.
Q01813448

7. GASI/GASM globalization for GLOBAL and CALA profiles.
support for Global and Cala has been added for Analog Stations.
Market-related parameters for all the supported profiles are downloaded 
from the Core through ASM+ messages.
Q01650292-01
Q01802889

8. Unanswered calls disconnect after just 6 minutes
Incoming trunk calls which are unanswered for 6 minutes are force 
disconnected by the BCM.
Q01785007-01

9. Issue with VoIP trunks locking up
After TRO happens on a VoIP trunk, there is a mismatch in the release 
sequence for a subsequent incoming call on the same trunk. This results in 
a VoIP trunk lockup.
Q01685091-03

10. Redirect information is incorrect after Blind Transfer when TRO is enabled
An incoming PR I call is tandemed from a CS1000 via VoIP to a BCM where it 
is answered. The BCM transfers the call to a second CS1000 via VoIP trunk 
where the call is "forward all calls" back to centralized voice mail on 
the first CS1000. When TRO is invoked to optimize the VoIP
trunks, the BCM sends incorrect redirection information to the first 
CS1000 so the transferred call lands in the general delivery mail box 
instead of the set mail box.
Q01594717-04

11. SRG50: Calling Party Privacy does not work When a set in Normal mode dials 
through VoIP to the SRG using the CS1000 presentation restricted feature
(no calling party number provided), the SRG substitutes its main number 
in the tandem call to the public network. In keeping with the presentation 
restricted feature, no calling party information should be provided.
Q01538245-03

12. Night service does not turn off on Mondays
The customer has night ringing service set up where the start and stop 
times change over the weekend. On Mondays, the night service does not 
turn off.
Q01781334-01

13. Redirection information is unknown in a particular scenario.
If the CS1000 ACDN is network call forwarded to a BCM and this call in turn
is forwarded back to CS1000 and TRO is enabled, log event 202 is generated
on the CS1000 due to unknown redirection reason.
Q01723403-01

14. DPNSS call cut off
When a tandem call is answered at a destination node and transferred back 
to the tandem node via a DPNSS link , the call is dropped after about 2 
minutes and the set is left in a locked up state until the user presses an 
intercom key and then release.
Q01688511-02

15. Call Diversion (Partial Rerouting) not Working on T-T Use r on BRI/M 
ETSI Call Diversion (partial re-routing) does not work when the T-T 
user setting is configured on a BRI module. It works fine when the 
S-T user setting is configured.
Q01788089-01

BCM50.R300.CORE-8
-----------------

1. GASI globalization.
Support for United Kingdom, Australia and
Poland has been added for Analog Stations.
Market-related parameters for all the
supported profiles are downloaded from the
CoreTel through the ASM_PLUS_INIT stimulus
messages.
Q01591658-02

2. Adaptive Line Tuning Support for GATM-Ver2.
Adaptive Line Tuning support is added in GATM-Ver2 firmware. This is to 
resolve the echo issues reported in multiple sites in different markets. 
This new Line Tuning Algorithm calculates the Filter Hybrid coefficients 
dynamically during boot-up based on the CO line conditions. GATM Adaptive 
Line tuning will only be supported on GATMv2 hardware and later vintages of 
GATM and combinations modules, which include the following top level codes:
Gx16 MBMs (NT5B42AAABE5/NT5B42AAACE5) & GATM 4/8 (NT5B44BAABE5/NT5BAAABE5).
Q01755111-03


