Software Update Name: BCM050.R500.CORE-TELEPHONY-119

Applicable H/W Platforms: BCM50, BCM50a, BCM50e, BCM50b, BCM50ba, BCM50be, SRG50

Applicable S/W Platforms: 9.0.1.00 through 9.0.1.XX 

Category: GEN 

Installation Recommendations:
This update should be applied to all new installations of BCM50 Release 5.0.,
and SRG50 5.0. Existing installations should have this update applied if they
are experiencing any of the issues that are corrected. There is no need to 
schedule specific maintenance to apply this upgrade if there are no reported
issues. In those cases, systems should be updated at the next regular service
opportunity.

Components and Versions:
 
   core-telephony 5.1.2.24.134
 
 
Dependencies:
   Required Updates:
   - BCM050.R500.SU.System-015.201202 or later

   Updates should be applied in the following order:
   - BCM050.R500.SU.System-015.201202 or later
   - BCM050.R500.CORE-TELEPHONY-119

Product Dependencies: None

Size: 3.99 MB

System Impact: 
Time to apply approximately 10 minutes

Does update application force reboot: Yes

Other Impacts: None

Limitations: 

- To enable the REFER functionality for SIP, the TAT functionality must be 
  enabled in the private network dialing plan. (Note: MCDN does not need
  to be enabled)

The following limitations are specific to BCM <-> SCS interoperability.


- Codec renegotiation during xfer to auto attendant on SCS.
  In this scenario, a call from PSTN gets tandemed to a set on SCS. The SCS
  user attempts to transfer to another SCS set, but it supports a different
  codec from what the first set on SCS supports. The transfer failed, because
  there is no overlap in the offered Codecs and the Codec supported by the
  target. The workaround is for all the SCS sets to support the same Codec.
  Q02036115

- CLID shows as anonymous during a double blind transfer.
  'Anonymous' shows up when testing the following scenario: 
  - Set1 on SCS calls PSTN through BCM 
  - Set1 blind xfers the call to set2 on SCS. On Set2, name is
  shown as transfer and DN of transferor is shown. 
  - Set2 then blind xfers the call to set3 on scs. On set3 we
  only see 'anonymous'. 
  Q02036122

Update Removable: No


Description:
------------
The following issues are addressed.
 
1.SIP Trunks get locked up
  When incoming SIP call contains the digits that match the destination/called systems
  destination codes and there is no Remote Access Package allowing the tandem call, the 
  SIP trunks get locked up. This update resolves the issue.
  wi01025217

This update includes the content of the following superseded updates:

BCM050.R500.CORE-TELEPHONY-107
==============================

1. Intercom key locked and unable to make or receive calls
   Set displays "No free buttons" while going off hook or trying to seize 
   the line after a TAT scenario. No calls can be made or received from 
   the problematic set. This update corrects the issue.
   wi00958750

2. Auto Attendant plays incorrect greeting.
   Incoming calls on T1 E&M auto answer trunks hear the generic greeting
   "enter the mailbox number or press # for company directory" when answered
   by the auto attendant.This update corrects the issue.
   wi00962042 


BCM050.R500.CORE-TELEPHONY-105
==============================

1. Crosstalk on IP sets when outgoing calls are made over PRI trunk.
   Crosstalk is heard on the IP set when an autodial key, configured with 
   the destination code is pressed to make an outgoing call on the PRI
   trunk. This update corrects the issue.
   wi00868013


BCM050.R500.CORE-TELEPHONY-98
==============================

1. After applying SU2-2 analogue line lock ups
   Calls which get answered by Auto Attendant through analog lines get locked 
   if the calling party disconnects the call without pressing any option of 
   the Auto Attendant. This update corrects the issue.  
   wi00856047

2. IP sets cease playing of Background Music 
   Intermittently, IP sets cease  playing the background music, even though
   the packet captures show music streaming to the phone on the correct ports.
   wi00856009


BCM050.R500.CORE-TELEPHONY-92
=============================

1. One way speechpath on meet me conference.
   Intermittently a one way speech path may occur when setting up  a 3 party
   conference CALL. If a conference member mutes himself and then disconnects
   from the conference, speech resources are not properly cleaned up. If 
   members of a  subsequent 3 party conference use this improperly released
   resource they may experience one way speechpath.
wi00875958

2. Tandem Calls from PRI -> BCM450 A - > SIP -> BCM 450 B - > SET get no CLID
   CLID intermittently displays on destination telephone after tandem from PRI
   to SIP.  Using the "INFO" button or Feature 811 only toggles Calling Name 
   and Line.  CLID does not display.
wi00892879

3. Intermittently one-way speech with Meet-Me conference.
   When a meet-me conference mutes himself and then goes into hold, now all
   the participants in the conference drop the call, the held participant
   will be released by the conference Server. The conference resource used
   by him remains in MUTE state. So for the next conference in the system 
   whichever participant is allocated with this MUTED.
   This update corrects this issue.
wi00839791

4. One way speech with Meet-Me conference
   When a meet-me conference user enters into the conference and gets unheld
   after being held. The user gets muted. This update corrects the issue.
wi00903480


BCM050.R500.CORE-TELEPHONY-80
==============================

1. Coretel crash due to invalid TN (logevent 115)
   This update corrects the referencing of NULL message pointer which results
   in a crash of the core telephony component.
wi00854606

2. Unable to leave VM when Telephony Audio Collection Service activated.
   When the Telephony Audio Collection Service (TACS) feature is invoked on a
   set and we try to invoke any Voice mail  on the same set, the voice mails
   sent to the called set do not get delivered. 
wi00860199

3. Cannot program KIM autodials and features using "drop-down" keys through 
   Element Manager Unable to  program KIM auto-dials and features "drop-down"
   keys through Element Manager once  a second KIM is added to a T7316E
wi00854261

4. VoIP trunking stops working and requires reconfiguration.
   Due to a Nill pointer reference the coretel component was crashing.
   This caused VoIP trunks to fail and after coretel came back up the VoIP 
   trunks had to be reconfigured. 
wi00848997


BCM50.R500.COMBO-78
====================

1. BCM50 R5 clicking on Dect hand sets fix.
   On a BRI cNIC card there was an issue with clock selection due to which
   the clicking sound was heard on the Dect set. This update resolves the
   issue.
wi00822131


BCM050.R500.CORE-TELEPHONY-72
=============================

1. Analog Set will ring continuously (FNA) or provide dead air (FB)
   SRG Analog Set will ring continuously (when set to Forward No Answer) 
   or provide dead air (when set to Forward Busy).
wi00831988

2. Tandemed SIP calls to PSTN fail if it does not answer within 10 seconds
   VoIP Gateway was ignoring the PROCEED message from Core and dropping the
   call if did not receive any other message within 10 seconds.
wi00729168


BCM050.R500.CORE-TELEPHONY-68
=============================

1. Target lines are locked up.
   Target lines assigned to a phone for incoming calls are locking up. A
   After customer speaks with caller and hangs up, the target line is 
   getting locked up. 
wi00729083

2. 8x16 has 4 ports stuck in enabling
   After upgrade to BCM 6.0 the upper four ports of an 8 port 
   analog trunk card will not enable. This affects GATM 8,
   8x16, and ADID8 modules.
wi00839353

3. MWI, tone OR lamp, for analog phones on ATA2 not working
   Sets connected to ATA hardware are rejecting MWI lamp / tone update requests.
Q02079632-01, wi00578097 


BCM050.R500.CORE-TELEPHONY-57
-----------------------------

1. KEMs reboot when moving lines using Feature *81
   When attempting to move lines from the main phone to the KEMs 
   or between KEMs using Feature *81 on three KEMS added, after
   the third or fourth move all KEM modules on the phone will
   start rebooting themselves and any lines previously moved in the
   same feature *81 session move back to their original location.
Q02156071

2. No ring back on tandem calls.
   Incioming calls to a target line which tandem out of the BCM are 
   disconnected after 2 rings if not answered, and the calling party
   does not hear ringback tone.
Q02160900

3. Direct pickup fails on SCS when call is originated from BCM
   Attempts to pick up BCM calls by SCS over SIP trunk were blocked by
   BCM not allowing REFER in unanswered state.
   See the note under 'Limitations'.
Q02102264-02

4. BCM <-> SCS interop: issue with Direct pickup on
   SCS when call is external to BCM 450r1
   An incoming PSTN call tandems via BCM over a SIP trunk to SCS
   where it rings at set A. If, while set A is ringing, SCS set B
   attempts direct call pickup, the call pickup will succeed but
   there will be no media path connection.
Q02130340-02

5. CLID does not appear on analogue set
   Due to some anomaly, when calling an Analogue set on a GASI port
   no CLID of calling number appears for an internal or external calls. 
Q02063636-03


BCM050.R500.CORE-TELEPHONY-53
-----------------------------

1. Cannot select facility for External Autodial in EM
   When programming an autodial using Element Manager one
   is not prompted to enter what facility should be used
   (Routing Table, Prime Line, Line Pool). 
Q02151428

2. Rotary Hunt Group not functioning correctly
   When an incoming call is blind transferred to a roatry hunt group, 
   The first available set in the HG only gets a short ring blip, but
   on completion of the transfer, the call  rolls to the next avialable set.
Q02146813

3. Call forward to Exchange UM fails with TRO on incoming call
   An incoming call to the SRG is forwarded to the users set in Normal
   mode on the main office. If TRO is active and the set actually has
   Call Forward All Calls setup on the main office to the Exchange UM
   server, the forwarded call will be disconnected.
Q02091162-02

4. Remote sites don't not get Ringback tone
   No ringback tone is audible to caller for outgoing tandem calls from
   BCM to PSTN on T1 E&M trunks to a BCM4.0 although call is
   actually ringing at the far end.
   This update resolves the issue.
Q02118568-03

5. No CLID transmission on transferred calls to CS1k over H.323 trunks
   When an incoming call to BCM transfers the active call
   to a CS1K set over h323 with f70 feature, the incoming
   line identifiers (CLID Information) are not transferred to customer.
Q02046221-02


BCM050.R500.CORE-TELEPHONY-50
-----------------------------

1. BCM 5.0 Issue see with core telephony when leaving a conference call - ref lost. 
   - If while recording a conference call, one of the conference participants 
     places the call on hold, on call release,  the speech connection may 
     not be properly released resulting in dangling resources.
   - A set makes an outgoing call to 2 external parties, conferences them 
     together and records the conference. If one of the external parties drops
     out of the conference, speech connection will be lost shortly after 
     with the remaining conference member.
Q02139464

2. Nnsupport option for remote modem enable failed.
   If a remote modem  session between the BCM  and IP destination
   is severed, attempts to reestablish the connection will occasionally
   fail since the BCM thinks the previous session is still active.
Q02150262

3. Cannot answer incoming calls to IPsets with KEMS using LAN CTE
   Under high traffic conditions, when IP sets with KEMs installed, 
   receive incoming calls they cannot be unable to answeed using
   LANCTE although all indictors are the TAPI is OK.
Q02149267  

4. Intermittent call drops when incoming calls are answered 
   Intermittently, incoming calls on analog lines are disconnected when
   answered.
   Q02091670-01


BCM050.R500.CORE-TELEPHONY-44
-----------------------------

1.Conference call is dropped
  An incoming and outgoing trunk are conferenced together
  through the BCM. When the set disconnects, the call
  is dropped instead of being transferred.
Q02115424-03
Q02144072

2. TRUNKS BECOME UNANSWERABLE 
   Incoming calls on analog trunks can get locked up while in
   the ringing state.
Q02144424

3. No speech path on SIP trunk to SIP trunk FMFM call 
   An incoming SIP call is directed to a destination set where 
   Find Me Follow Me is enabled. The call tandems to 2 
   FMFM destinations. When the call is asnswered there
   is no speech path. This update resolves the issue.
Q02136227

4. Multiple Business Name version error in upgrade code.
   The MBN upgrade code does not update the version
   ID correctly for the MBN data structure. 
   This can result in lost or defaulted data.
Q02140413

5. DND icons disappearing from KEMs attached to 1230 sets
   KEM icons may incorrectly display a monitored set as idle
   when it is in fact in Do Not Disturb mode.
Q02076812-03


BCM50.R500.MBN-37
------------------

1. Core telephony crash 
   This problem could occur when an IP trunk with multiple
   associated media paths released a call. If an IP trunk has
   2 or more media paths assigned when it released there is 
   a possibility for the  Coretel software to enter an
   infinite loop and lock up. 

   An IP trunk could end up with 2 or more media paths
   either by :

   - multiple sets alerting for a call on the trunk, or, 
   - additional media paths assigned via a spurious
     media path connect request which creating an extra
     media path when a set blind transfers a call to an
     IP trunk. (released while hearing the ringback.) 

   In either case, if the IP trunk has multiple media
   paths assigned then when the IP trunk call is released
   resyulting in  an infinite loop (software lockup).

   This update 

   - prevents Core Telephony from sending a request to
     connect a media path when not required (preventing
     unexpected multiple media paths assigned to IP trunks), and
   - repairs a s/w error that could result in an infinite
     loop when an IP trunk with multiple media paths releases.
   Q02133182

2. Intermittent Caller ID Failure
   Intermittently Caller ID information is not presented
   on the destination set for incoming calls over analog lines.
   Q02074343-03


3. CoreTel reset during multi-part conference disconnect.
   When a multi party conference call was being released
   the core telephony component crashed due to a NULL
   poiner reference.
   Q02117999


4. Can not cancel Hot Desking after transferring a call
   Set A, B, C and D: register to the BCM
   1. From set B, use feature *999 to hot desking set A
   2. From set C, press Intercom line and dial DN of set A.
   3. Receive the call on set B and transfer the call to set D.
   4. Set D receive the call and two way speech path is
      established between C and D. Set B released from the call
      by pressing Join soft key.
   5. If one tries to Cancel hot desking from set A, it will be denied
      with a message announcing set B is on an active call.
   Q01899589-01

5. Incoming DID redirected over MCDN SIP to CS1K CP AA is disconnected
   An incoming DID call which tandems through a BCM to a CS1K where
   it is answered by the CS1K Auto Attendant is disconnected with
   a release reason of "interworking unspecified."
   Q02091716-03

6. TAPI agent cannot join held call
   An incoming held call cannot be retrieved using TAPI E911
   applications. 
   Q02111952-02

7. Updated Network Name display allows per set / hunt group
   business name + sending of longer name
   The update provides Multiple Business Name facilities on a single 
   BCM such that a single system can represent multiple "sub-tenants" 
   from a Network Name Display perspective.

   - A Bcm now has up to 5 unique Business Names.
     o During an upgrade the previous single Business Name will
       be copied to Business Name 1.

   - Each Set and Hunt group in the BCM can be associated with
     1 of the 5 business names, or no Business Name (None).
     o By default, each Set & HG is associated with Business Name 1.

   - When Network Name Display (NND) is to be generated for a
     related Set/HG's call, the associated Business Name 
     (1 - 5, None) will be used.

   - Each Set and HG now has a "Long Name" field (up to 15 
     characters).  
     o This field is used for NND only.
     o During an upgrade the current Set/HG name will be copied
       to the Long Name field.
     o There is an associated check-box "Use Long Name?".
       The default value is No (unchecked).
     o If Use Long Name is Yes, then this Long Name will be
       used in place of the Set or HG name when NND is to be
       generated for a call.

    - All NND truncation rules remain the same.   
      o A generated NND can not exceed 15 characters total.
      o Set or HG [long] name being used in the NND will be
        truncated sufficiently such that the NND is no more
        than 15 characters.
      o There is no automatic insertion of a space ' ' between
        the Business Name and Set/HG [long] name in the generated
        NND.
    Q02100149

8. CLID not displayed on Cfwd across SIP to BCM 5.0
   When a Call is Call forwarded to another BCM 5.0 via SIP
   trunks CLID does not get passed to the receiving set.
   Q02105118

9. Unable to re-direct a line to an international phone number via Element manager
   Unable to re-direct a line to an international phone number
   via element manager. One can successfully redirect the call 
   for the same line and number using F84 from a telephone set.
   Q02112366

10. SIP calls not disconnecting properly
   In some SIP call scenarios, it was found that as part of 
   disconnecting a call, BCM will send a re-invite to put a
   call on hold and then BCM sends a BYE. This can 
   cause an  IP trunk to lock up.  
   Q02109019

11. IP phone display changes from French to English
   An IP set is configured to display in French. The user changes the name of an
   extension on the system using Feat**CONFIG. The display turns to English and
   Feat*502 no longer works to revert it back to French.
   Q02038936-01
