Contents | Index | Previous | Next

KEY

basic-1

xx aaa yyyy (cccc or D) zz..z

Telephone function key assignments

The following key assignments determine calling options and features available to a telephone. Note that KEY is prompted until just a carriage return <cr> is entered.

Where:

BULLET.gif xx = key number

BULLET.gif aaa = key name or function

BULLET.gif yyyy = additional information required for the key

BULLET.gif cccc = CLID entry of (0)-N, where N = the value entered at the SIZE prompt in LD 15 minus 1.

BULLET.gif zz..z = additional information required for the key aaa.

The cccc or D entry deals specifically with the Calling Line identification feature. Where:

BULLET.gif cccc = CLID table entry of (0)-N, where N = the value entered at the SIZE prompt in LD 15 minus 1.

BULLET.gif D = the character "D". When the character "D" is entered, the system searches the DN keys from key 0 and up, to find a DN key with CLID table entry. The CLID associated with the found DN key will then be used.

With X11 Release 23, ISDN is not required for Calling Line Identification entry.

Note: The position of the (cccc or D) field varies depending on the key name or function.

You may enter a CLID entry if aaa = ACD key, HOT d, HOT L, MCN, MCR, PVN, PVR, SCN or SCR. Type xx NUL to remove a key function or feature.

Some data ports require specific key assignments. Refer to the Meridian Data Services NTPs for information regarding these requirements.

Where key assignments may be:

BULLET.gif 0-5 for M2006

BULLET.gif 0-7 for M2009

BULLET.gif 0-59 for M2616

BULLET.gif 0-69 for SL1, varies with the number of key/lamp strips

If either the Meridian Programmable Data Adapter (MPDA) or the Display Module is equipped, then key 7 on sets M2008, M2216, and M2616 sets and key 5 on set M2006 will become Program keys which cannot be used as function keys.

Any printout of the TN block will not show key 7 because it is a local function key.

On the M2616, if CLS = HFA, key 15 on the voice TN defaults to the Handsfree key. No other feature assignment is accepted.

Primary and secondary data DNs must be unique.

A station SCR, SCN, MCR, or MCN DN must be removed as a member from all Group Hunt lists before the DN can be modified.

basic-24

On the M3903, keys 4-15 are blocked. No feature assignment is accepted for keys 2-15.

On the M3903,M3904, M3905, keys 27-31 are reserved. No feature assignment is accepted for keys 17-31 other than NUL.

On M3904, no feature assignment is accepted for keys 12-15.

On M3905, the craftsperson can assign NUL or a server application on key 5. On key 6, the craftsperson can assign NUL or a local application.

On M3905, the craftsperson can assign NUL or the program key on key 7.

On M3905, the craftsperson can assign AAG, AMG, ASP,DWC, EMR, MSB, or NRD on keys 8-11. Other features are blocked.

acdb-1

xx AAG

ACD Answer Agent key

Must have CLS = SPV.

basic-24

On the M3905 key numbers 8-11 are reserved for AAG, AMG, ASP, DWC, MSB and NRD.

aab-1

xx AAK

Automatic Answerback key

AAA CLS and AAK key cannot be assigned to the same telephone. Only one type of Automatic Answerback is allowed. M2616 telephone must have CLS = HFA.

bacd-1

xx ACD yyyy (cccc or D) zzz

Automatic Call Distribution key

Where:

BULLET.gif xx = key number (must be key 0)

BULLET.gif yyyy = ACD DN or Message Center DN

BULLET.gif cccc = CLID table entry of (0)-N, where N = the value entered at the SIZE prompt in LD 15 minus 1.

BULLET.gif D = the character "D". When the character "D" is entered, the system searches the DN keys, from key 0, up to find a DN key with CLID table entry. The CLID associated with the found DN key will then be used.

BULLET.gif zzzz = agent's position ID

yyyy and zzzz can be up to 4 digits, up to 7 digits with Directory Number Expansion (DNXP) package 150. Only ACD DN for Option 11C model set.

acdd-13

xx ACNT

Activity Code entry key

This key must have an associated lamp and applies to ACD-D and ACD-MAX only. ADS data block must be configured in LD 23. For Release 13 and later.

optf-1

xx ADL yy z...z

Autodial key

Where:

BULLET.gif xx = key number

BULLET.gif yy = maximum length of the ADL DN. Prior to Release 22, valid entries are: 4, 8, 12, (16), 20, 23. For Release 22, valid entries are: 4, 8, 12, (16), 20, 24, 28, 31. Note that other values are rounded up to the next valid number.

BULLET.gif z...z = actual Autodial DN (this entry is optional)

bacd-1

xx AGT yyyy

ACD Agent status key

Where: yyyy = agent's ID. The agent ID number can be up to 4 digits, up to 7 digits with Directory Number Expansion (DNXP) package 150. Must have CLS = SPV.

acdb-1

xx AMG

ACD Answer Emergency call key

Must have CLS = SPV.

For x11 release 22, the Answer Emergency Key can be defined as a secondary supervisor's Position ID. The secondary supervisor's Position ID can be NULL by default.

The Position ID of the ACD set cannot be changed once the ACD set is acquired as a Human Agent.

basic-1

xx AO3

Three-Party Conference key

basic-24

On the M3902 key number 4 is reserved for AO3, AO6, TRN, or NUL

basic-24

On the M3903, M3904, M3905 key number 18 is reserved for AO3, AO6, or NUL.

mit-25

On theI2004 key number 18 is reserved for AO3, AO6, or NUL.

basic-1

xx AO6

Six-Party Conference key

basic-24

On the M3902 key number 4 is reserved for AO3, AO6, TRN, NUL

basic-24

On the M3903, M3904, M3905 key number 18 is reserved for AO3, AO6, or NUL.

mit-25

On theI2004 key number 18 is reserved for AO3, AO6, or NUL.

basic-1

xx ARC

Attendant Recall key

acdb-1

xx ASP

ACD Supervisor call key (must have CLS = AGN)

basic-24

On the M3905 key numbers 8-11 are reserved for NRD, MSB, AAG, AMG, DWC and ASP.

supp-14

xx ATW

ACD Call Waiting Time indication key

bacd-1

xx AWC

ACD Calls Waiting key

Must have CLS = AGN and Supervisor Position ID or SPID must be configured.

bfs-20

xx BFS TN

Busy Forward Status key

Where: TN = Terminal Number to be screened. A Key cannot be assigned to a BRI set.

Note: It is possible to configure the TN of the same set against the BFS key only if the Class of Service is BFEA.

basic-14

xx CA yy z...z

Combined No Hold Conference and Autodial key

Where:

BULLET.gif yy = maximum length of the CA DN. Valid entries are: 4, 8, 12, (16), 20, 24, 28, 31. Note that other values are rounded up to the next valid number.

BULLET.gif z...z = actual Autodial DN (this entry is optional)

casm-1

xx CAS

Centralized Attendant Service key

optf-1

xx CFW yy z...z

Call Forward key

Where: yy = maximum length of the CFW DN

Prior to Release 22, valid entries for yy are: 4, 8, 12, (16), 20, 23. Numbers between 4 and 23 are rounded up to the next valid number.

If Release 22 and later, valid entries for M2317 or M3000 sets are any integer in the range of (4)-23. For all other BCS type sets, you may enter any integer in the range of (4)-31.

Where: z...z = Call Forward DN or range of DNs where calls are to be forwarded (the target DN). Must be key 11 for LOGIVOX telephones.

A Group Hunt DN can be entered. If CLS = CFXD, the Call Forward number must be an internal DN.

basic-24

On the M3903, M3904, M3905 key number 19 is reserved for CFW or NULL.

mit-25

On the I2004 key number 19 is reserved for CFW or NULL.

basic-14

xx CH D yy z...z

Combined No Hold Conference and Direct Hotline key

Where:

BULLET.gif yy = number of digits in target DN (1-31)

BULLET.gif z...z = target DN

basic-14

xx CH L yyy

Combined No Hold Conference and Hotline List key

Where: yyy = 0-999 for Hotline list entry as defined in LD 18. Applies to Release 14 and later.

chg-1

xx CHG

Charge account key

basic-24

On the M3903, M3904, M3905 key number 25 is reserved for CHG or NUL.

mit-25

On the I2004 key number 25 is reserved for CHG or NUL.

ccos-7

xx CLT

Configure Callers List key in context sensitive area, CLT/NUL are only options for key 27. On the M3903, M3904 and M3905, key number 27 is reserved for the CLT or NUL mnemonic.

basic-25.4

xx COS

Controlled Class of Service key

chg-1

xx CPN

Calling Party Number key

basic-24

On the M3903, M3904, M3905 key number 26 is reserved for CPN or NUL.

mit-25

On the I2004 key number 25 is reserved for CPN or NUL.

basic-14

xx CS yyyy

Combined No Hold Conference and Speed Call key

Where: yyyy = Speed Call list number from 0-8190. Not available on M3000 telephones.

basic- 23

xx CSD

Conferee Selectable Display key.

basic-1

xx CWT

Call Waiting key

Only one CWT Key is allowed. Should have CLS = HTD since Hunting takes precedence.

bacd-1

xx DAG

Display ACD Agents key

This key displays the status of ACD agents appearing on the supervisor's telephone. Must have CLS = SPV and ADD or DDS.

di-1

xx DIG yyyy zz R/V

Dial Intercom Group key

Where:

BULLET.gif yyyy = group number, from 0-253. For Release 13 and later from 0-2045.

BULLET.gif zz = member number from 0-99. The zz value cannot be equal to or share the first digit of a 2 digit number with the SPRE code. For example, if SPRE = 1, zz cannot be 1, 10, 11...19.

BULLET.gif R = Ring option

BULLET.gif V = Voice option

Must have maximum number of Dial Intercom Groups DGRP defined in LD 15.

If any member in a group has a two-digit member number, then all members have a two-digit number. The system adds leading zeros to other entries.

Prompted with Dial Intercom (DI) package 21.

dcp-12

xx DPU

Directed Call Pickup key

Key is optional, dial access code can be used if CLS = DPUA. Not available on M3000 telephones. This prompt appears with Directed Call Pickup (DCP) package 115.

basic-15

xx DRC yyy

DID Route Control key

Where: yyy = route number = 0-511

ddsp-1

xx DSP

Display key

This key must have an associated key/lamp pair.

bacd-19

xx DWC yyyy

ACD Supervisor Display Waiting Calls key

Where: yyyy = ACD DN. Up to 4 digits, up to 7 digits with Directory Number Expansion (DNXP) package 150.

A maximum of eight DWC keys can be assigned per queue on eight supervisors. Agent sets can only have 1 SWC key for their own queue.

With X11 release 19 and later, ACD agent telephones can support the display waiting calls key. Must have CLS = SPV and ADD or DDS.

With X11 release 19 and later, the key can be used with supervisors and agents. Prior to release 19, this key applied only to supervisor telephones.

basic-24

On the M3905 key numbers 8-11 are reserved for AAG, AMG, ASP, DWC, MSB and NRD.

acdb-1

xx EMR

ACD Emergency key (must have CLS = AGN)

basic-24

On the M3905 key numbers 8-11 are reserved for AAG, AMG, ASP, DWC, MSB and NRD.

acdb-1

xx ENI yyyy

ACD Enable Interflow key

Where: yyyy = DN. The DN can be up to 4 digits, up to 7 digits with Directory Number Expansion (DNXP) package 150.

Only one is allowed per ACD DN. Must have CLS = SPV.

povr-20

xx EOVR

Enhanced Override key

pldn-15

xx FDIS

Force Disconnect key

ponw 26

xx GHD

Group Hunt Deactivation key

A station user can toggle the PDN in and out of all groups of which that PDN is a member.

dcp-12

xx GPU

Group Call Pickup key

The key is optional because a dial access code can be used if CLS = GPUA. Not available on M3000 telephones. Allowed with Directed Call Pickup (DCP) package 115.

grp-1

xx GRC yy

Group Call key

Where: yy = 0-63 for Group number as defined in LD 18

supp-10

xx HLD

Hold

hot-10

xx HOT

Direct entry for Hotline model set key (Option 11C), Automatic termination DN is eight digits

hot-21

nn HOT D dd num DN m (cccc or D)

Two-way Hotline key

Where:

BULLET.gif dd = number of digits dialed

BULLET.gif num = target_number (terminating DN is a maximum of 31 digits)

BULLET.gif DN = two-way hotline DN

BULLET.gif m = one of the following Terminating Modes: H = Hotline (default), N = Non-ringing, R = Ringing, or V = Voice

BULLET.gif cccc = CLID entry of (0)-N, where N = the value entered at the SIZE prompt in LD 15 minus 1.

BULLET.gif D = the character D may be entered to search a CLID entry from key 0 and up to find a DN key. The CLID associated with the found DN key will then be used.

hot-10

xx HOT D nn x...x

Direct entry for One-way Enhanced Hotline key, where:

BULLET.gif nn = number of digits dialed

BULLET.gif x...x = Hotline terminating DN up to a 31 digit maximum

hot-10

xx HOT D nn x...x xxxx (cccc or D)

Direct entry for Two-way Enhanced Hotline key, where:

BULLET.gif nn = number of digits in Target DN

BULLET.gif x...x = Terminating DN up to a 31 digit maximum

BULLET.gif xxxx = optional two way Hotline DN. The DN can be up to 4 digits, up to 7 digits with Directory Number Expansion (DNXP) package 150.

BULLET.gif cccc = CLID entry of (0)-N, where N = the value entered at the SIZE prompt in LD 15 minus 1.

BULLET.gif D = the character D may be entered to search a CLID entry from key 0 and up to find a DN key. The CLID associated with the found DN key will then be used.

hot-21

nn HOT I dd num m

Intercom key

Where:

BULLET.gif dd = number of digits dialed

BULLET.gif num = target_number (terminating DN max 31 digits)

BULLET.gif m = one of the following Terminating Modes: V = Voice (default), N = Non-ringing, or R = Ringing

hot-10

xx HOT L bbb

One-way Hotline key

Where: bbb = Hotlline list entry = 0-999. The Hotline list entry is defined in LD 18.

Note: That the Hotline list NCOS overrides the set NCOS.

hot-10

xx HOT L bbb xxxx (cccc or D)

Two-way list entry for Enhanced Hotline key

Where:

BULLET.gif bbb = List entry = 0-999

BULLET.gif xxxx = Two-way Hotline DN. This DN can be up to 4 digits, up to 7 digits with Directory Number Expansion (DNXP) package 150.

BULLET.gif cccc = CLID entry of (0)-N, where N = the value entered at the SIZE prompt in LD 15 minus 1.

BULLET.gif D = the character D may be entered to search a CLID entry from key 0 and up to find a DN key. The CLID associated with the found DN key will then be used.

Hotline list entry is defined in LD 18.

Note: That the Hotline list NCOS overrides set NCOS.

icf-19

xx ICF nn xxxx

Internal Call Forward key

Where: nn = Forward DN length. Prior to release 22, valid entries are: 4, 8, 12, (16), 20 and 23. Other ICF DN entries between 4 and 23 are rounded up to the next valid number. For Release 22 and later, valid entries are any integer in the range of (4)-31.

Where: xxxx = Forward DN (this entry is optional)

An ICF key can be configured if Call Forward is enabled.

supp-10

KY1 aaa

Key 1 located far left, below dial pad.

Where: aaa = VUP (Volume Up) by default for KY1. Any function not requiring a lamp may be assigned. CLS must be LVXA.

KY2 aaa

Key 2 located middle, below dial pad.

Where: aaa = VDN (Volume Down) by default for KY2. Any function not requiring a lamp may be assigned. CLS must be LVXA.

KY3 aaa

Key 3 located far right, below dial pad.

Where: aaa = HLD (Hold) by default for KY3. Any function not requiring a lamp may be assigned. CLS must be LVXA.

dlt2-9

29 LNG

M2317 Language Toggle key (No Language)

Where:

BULLET.gif xx = key 29

BULLET.gif LNG = Language Toggle enabled

BULLET.gif NUL = Remove Language Option

This feature allows set operator to set and reset language display, toggling between French and English versions on the alphanumeric display.

Inr-8

xx LNK

Last Number Redial key

LNRS defines the Last Number Redial Size.

For LOGIVOX telephones, key 8 is defined by set firmware as the Last Number Redial key. The key definition is optional, because the user can press the DN key twice to activate Last Number Redial.

Must have OPT = LRA in LD 15 and CLS = LNA.

ohol-20

Loudspeaker key

xx LSPK yyyy

Where: yyyy = associated loudspeaker DN or SPEKABUS channel

xx MCK

Message Cancellation Key

mwc-1

This key should only be programmed on Message Center sets.

basic-20

Multiple Call Non-Ringing key

xx MCN yyyy (cccc or D)zz..z

Where:

BULLET.gif yyyy = DN

BULLET.gif cccc = CLID entry of (0)-N, where N = the value entered at the SIZE prompt in LD 15 minus 1.

BULLET.gif D = the character D may be entered to search a CLID entry from key 0 and up to find a DN key. The CLID associated with the found DN key will then be used.

BULLET.gif zz..z = additional information required for the key aaa.

The DN can be up to 4 digits, up to 7 digits with Directory Number Expansion (DNXP) package 150. The DN cannot appear simultaneously on a PBX set DN or as an SCR DN or SCN DN.

With Release 18 and later, once the MCN key has been defined, MARP is prompted.

basic-24

On the M3901 and M3902 MCN cannot be configured on keys 1-5. MCN, if it is configured, must be assigned to key 0.

basic-20

xx MCR yyyy (cccc or )zz..zD

Multiple Call Ringing key

Where:

BULLET.gif yyyy = DN

BULLET.gif ccc = CLID entry of (0)-N, where N = the value entered at the SIZE prompt in LD 15 minus 1.

BULLET.gif D = the character D and may be entered to search a CLID entry from key 0 and up to find a DN key. The CLID associated with the found DN key will then be used.

BULLET.gif zz..z = additional information required for the key aaa.

The DN can be up to 4 digits, up to 7 digits with Directory Number Expansion (DNXP) package 150. The DN cannot appear simultaneously on a PBX set DN or as a SCR Single Call or SCN DN.

With Release 18 and later, once the MCR key has been defined MARP is prompted.

basic-24

On the M3901 and M3902 MCR cannot be configured on keys 1-5. MCR, if it is configured, must be assigned to key 0.

mwc-1

xx MIK

Message Indication Key

This key should only be programmed on Message Center sets.

amp-5

xx MMM

Voice/Data display key

Only key numbers 0-7 can be assigned for the M2008. M2x16 varies with additional add-on modules. Maximum key number is 59.

The Data Port requires specific key assignments. An ISDLC line card, vintage C or higher, is required for M2006, M2008, M2216 and M2616 telephones.

mr-10

xx MRK

Message Registration Key

Requires PPM/Message Registration (MR) package 101 and CLS = ADD or DDS.

msb-1

xx MSB

Make Set Busy key

basic-24

On the M3905 key numbers 8-11 are reserved for AAG, AMG, ASP, DWC, MSB and NRD.

mwc-1

xx MWK yyyy

Message Waiting Key

Where: yyyy = DN.

The DN can be up to 4 digits, up to 7 digits with Directory Number Expansion (DNXP) package 150. With the Network Message Service feature equipped, the NMS-DN can be up to 13 digits.

basic-24

On the M3902, key 5 is reserved for MWK or NUL.

On the M3903, M3904, M3905, key 16 is reserved for MWK or NUL.

mit-25

On the i2004 key 16 is reserved for MWK or NUL.

basic-14

xx NHC

No Hold Conference key

bacd-1

xx NRD

Not Ready key

AGN or SPV Class of Service must be assigned.

basic-24

On the M3905 key numbers 8-11 are reserved for AAG, AMG, ASP, DWC, MSB and NRD.

bacd-12

xx NSVC yyyy

Night Service key (must have CLS = SPV)

Where: yyyy = ACD DN associated with that Night Service. The DN can be up to 4 digits, up to 7 digits with Directory Number Expansion (DNXP) package 150.

basic-1

xx NUL

Removes function or feature from key

bacd-12

xx OBV

Observe ACD agent key (must have CLS = SPV)

esa- 23

xx OSN

On-Site Notification key.

aop-1

xx OVB

Overflow Position Busy key

optf-1

xx OVR

Override key

cprk-2

xx PONW

Priority Override/BreakIn Network-wide key.

ponw-26

xx PRK

Call Park key

The Transfer (TRN), or Six-Party Conference (A06) key plus a Dial Access code can be used instead of the Park key.

basic-24

On the M3903, M3904, M3905, key 21 is reserved for PRK or NUL.

mit-25

On the i2004 key 21 is reserved for PRK or NUL.

basic-1

xx PRS

Privacy Release key

basic-24

On the M3903, M3904, M3905, key 24 is reserved for PRS or NUL.

mit-25

On the i2004 key 24 is reserved for PRS or NUL.

basic-20

xx PVN yyyy (cccc or D)zz..z

Private Line Non-Ringing key

Where:

BULLET.gif yyyy = DN

BULLET.gif cccc = CLID entry of (0)-N, where N = the value entered at the SIZE prompt in LD 15 minus 1.

BULLET.gif D = the character D may be entered to search a CLID entry from key 0 and up to find a DN key. The CLID associated with the found DN key will then be used.

BULLET.gif zz..z = additional information required for the key aaa.

The DN can be up to 4 digits, up to 7 digits with Directory Number Expansion (DNXP) package 150. Must have Private Line Directory Number (PRDN) defined in LD 14.

basic-24

On the M3901, M3902, key 0 is reserved for PVN.

basic-20

xx PVR yyyy (cccc or D)zz..z

Private Line Ringing key

Where:

BULLET.gif yyyy = DN

BULLET.gif cccc = CLID entry of (0)-N, where N = the value entered at the SIZE prompt in LD 15 minus 1.

BULLET.gif D = the character D may be entered to search a CLID entry from key 0 and up to find a DN key. The CLID associated with the found DN key will then be used.

BULLET.gif zz..z = additional information required for the key aaa.

The DN can be up to 4 digits, up to 7 digits with Directory Number Expansion (DNXP) package 150. Must have Private Line Directory Number (PRDN) defined in LD 14.

basic-24

On the M3901, M3902, key 0 is reserved for PRV.

acdb-1

xx RAG

ACD Ring Agent key (must have CLS = SPV)

rck-15

xx RCK y z

Ringing Change Key

Where:

BULLET.gif y = first key/lamp strip controlled by key = (0)-6

BULLET.gif z = second key/lamp strip controlled by key = 0-(1)-6.

Only one ringing change key per set is permitted. Requires International Supplementary Features (SUPP) package 131 and Ringing Change Key (RCK) package 193.

snr-3

xx RDL yy

Redial stored number key

Where: yy = number of digits = 4, 8, 12, (16), 20, 23. Numbers between 5 and 22 are rounded up to the next valid number.

rga/ optf-20

xx RGA

Ring Again key

Must be key 10 on LOGIVOX telephones. RANA may be activated if OPT = RNA in LD 15. When OPT = RND in LD 15, all sets with the RGA key will only be able to activate Ring Again Busy.

basic-24

On the M3903, M3904, M3905, key 20 is reserved for RGA or NUL.

mit-25

On the i2004 key 20 is reserved for RGA or NUL.

basic-1

xx RLS

Release key

Requires CLS = LVXA. Key/lamp pair is not required. Must be KY3 on LOGIVOX telephones.

rms-10

xx RLT

Configure Redial List key in context sensitive area, RLT/NUL are only options for key 28. On the M3903, M3904 and M3905, key number 28 is reserved for the RLT or NUL mnemonic.

basic-25.4

xx RMK

Room Status Key

mw-24

xx RMWK xxxx [yyyy]

Remote Message Waiting indication key

Where:

xx= key number

xxxx = Message Center DN

[yyyy] = DN to be monitored [optional]

basic-1

xx RNP yyyy

Ringing Number Pickup key

Where: yyyy = Ringing Number Pickup group number is optional

If the group number is not entered, the key will pick up the group number assigned to the station. If the group number is entered, the key will pick up calls in the specified group yyyy.

basic-24

On the M3903, M3904, M3905, key 22 is reserved for RNP or NUL.

mit-25

On the i2004 key 22 is reserved for RNP or NUL

rpa-15

xx RPAG yyyy

Radio Paging key

Where: yyyy = Route Access Code

Releases 16 and later allow Coordinated Dialing Plan (CDP) Trunk Steering Codes (TSC) and Distant Steering Codes (DSC) to be entered against yyyy.

optf-1

xx SCC yyyy

Speed Call Controller key

Where: yyyy = SCL list number = 0-253 prior to Release 13, 0-8190 Release 13 and later. SCL must be defined in LD 18.

basic-24

On the M3903, M3904, M3905, key 23 is reserved for SCC, SCU, SSU, SSC or NUL.

basic-20

xx SCN yyyy (cccc or D) zz..z

Single Call Non-Ringing key

Where:

BULLET.gif yyyy = DN

BULLET.gif cccc = CLID table entry of (0)-N, where N = the value entered at the SIZE prompt in LD 15 minus 1.

BULLET.gif D = the character "D". When the character "D" is entered, the system searches the DN keys from key 0 and up, to find a DN key with CLID table entry. The CLID associated with the found DN key will then be used.

BULLET.gif zz..z = additional information required for the key aaa.

The DN can be up to 4 digits, up to 7 digits with Directory Number Expansion (DNXP) package 150. With Releases 18 and later, once the SCN key has been defined, MARP is prompted.

basic-24

On the M3901, M3902, key 0 is reserved for SCN.

basic-20

xx SCR yyyy (cccc or D) zz..z

Single Call Ringing key

Where:

BULLET.gif yyyy = DN

BULLET.gif cccc = CLID table entry of (0)-N, where N = the value entered at the SIZE prompt in LD 15 minus 1.

BULLET.gif D = the character "D". When the character "D" is entered, the system searches the DN keys from key 0 and up, to find a DN key with CLID table entry. The CLID associated with the found DN key will then be used.

BULLET.gif zz..z = additional information required for the key aaa.

The DN can be up to 4 digits, up to 7 digits with Directory Number Expansion (DNXP) package 150. Use a single appearance DN to terminate VCC Voice Call or SIG Signaling calls.

With Release 18 and later, once the SCR key has been defined, MARP is prompted.

basic-24

On the M3901, M3902, key 0 is reserved for SCR.

optf-1

xx SCU yyyy

Speed Call User key

Where: yyyy = SCL list number = 0-253 prior to Release 13, 0-8190 in Release 13 and later. SCL must be defined in LD 18.

basic-24

On the M3903, M3904, M3905, key 23 is reserved for SCC, SCU, SSU, SSC or NUL.

mit-25

On the i2004 key 23 is reserved for SCC, SCU, SSU, SSC or NUL.

basic-1

xx SIG yyyy

Signal key

Where: yyyy = Single appearance DN.

The DN can be up to 4 digits, up to 7 digits with DNXP package 150. Key/lamp is not required.

optf-1

xx SSC yyyy

System Speed Call controller key

Where: yyyy = SSC list number = 0-253 prior to Release 13, 0-4095 in Release 13 and later. SSC list must be defined in LD 18.

basic-24

On the M3903, M3904, M3905, key 23 is reserved for SCC, SCU, SSU, SSC or NUL.

optf-1

xx SSU yyyy

System Speed Call User key

Where: yyyy = SSC list number = 0-253 prior to Release 13, 0-4095 Release 13 and later. SSC list must be defined in LD 18.

ddsp-1

xx TAD

Time and Date key

For SL-1 sets only, must have CLS = ADD or DDS, cannot be key 0.

thf-14

xx THF

Centrex Trunk Switch Hook Flash key

mct-10

xx TRC

Malicious Call Trace key

Key/lamp not required. MCT is applied on a TN basis. For Release 19 and later, this key can be configured on ACD telephones. Allowed when CLS = MCTA.

basic-1

xx TRN

Call Transfer key

On the M3902, key 4 is reserved for TRN or NUL.

basic-24

On the M3903, M3904, M3905, key 17 is reserved for TRN or NUL.

mit-25

On the i2004 key 17 is reserved for TRN or NUL.

uscr-19

xx USR

User Selectable Call Redirection key

ims-2

xx UST

User Status key (must have UST = YES in LD15 and UST = YES in LD 23)

basic-1

Voice Call key

xx VCC yyyy

Where: yyyy = Single appearance DN. Not available on M3000 telephones.

xx VUP

Volume Up key (must be assigned if Volume Down is assigned)

xx VDN

Volume Down key (must be assigned if Volume Up is assigned)

gewu-16

xx WUK

Guest entry of automatic Wakeup key (Key/lamp pair is required)

mw-24

Extended Message Waiting indication key

xx XMWK xxxx yyyy

Where:

BULLET.gif xx= key number

BULLET.gif xxxx = Message Center DN

BULLET.gif yyyy = DN to be monitored