The Switch Information page in the Configuration Wizard enables you to
enter the required switch information
configure the channels
The
switch and channel information required in the Configuration Wizard is
almost identical between the Meridian 1 switch and Succession 1000 system.
Differences are noted where applicable.
Click the highlighted text in the table below for more details, or scroll
down.
|
Topic |
Description |
|
An explanation of the terms used to identify the server and switch connectivity components. | |
|
Required to establish the connection between the CallPilot server and the switch. | |
|
Required only if you purchased the Symposium Voice Services Support feature. If Access Channels is set to 0 on the Feature Verification page, then the Symposium Voice Services Support feature was not purchased. | |
|
The TN, Key 0, and Key 1 information for CallPilot channels. |
Configuration Wizard > Configuration Mode > Keycode and Serial Number > Feature Verification > Server Information > Password Information > Multimedia Allocation > Switch Information
Follow the instructions on the Configuration Wizard pages until you reach the Switch Information page.
Follow the instructions in the remainder of this Help topic.
Click Next.
For Meridian 1 and Succession 1000, the switch telephony interface (STI) boards are the MPB boards in the CallPilot server. These MPB boards are connected to one or more MGate cards in the switch through a DS30X cable.
The left side of the page lists the detected switch telephony interface
boards. These are labeled as follows:
|
IF the server is a |
THEN CallPilot displays |
|
200i server |
STI Board 1 (200i). |
|
201i server |
STI Board 1 (201i). |
|
Tower or rackmount server |
STI Board n (board_name), where
|
Each DS30X link is labeled Link STIxx-yyy, where xx is the switch telephony interface board slot number, and yyy identifies the specific link that is connected to the switch telephony interface board.
Each MPB16-4 board has two possible links (STIxx-001 and STIxx-002). Individual call channels (also referred to as DS0 channels) on each link are identified as STIxx-yyy-zzzwhere zzz is the individual channel on link STIxx-yyy.
An MPB16-4 board is in slot 2. This MPB16-4 board is connected to 2 MGate cards through a double DS30X cable (NTRH2013). These two links appear as STI02-001 and STI02-002.
In the Channel Name column, individual channels on link STI02-001 are identified as STI02-001-001, and so on.
You must specify the following information for your Meridian 1switch
or Succession CSE 1000 system:
|
Item |
Description |
|
Switch IP Address |
Enter the IP address of the Meridian 1 switch or Succession 1000 system. |
|
Switch Type (applicable for |
Choose M1 or M1 Option 11.
|
|
Switch Customer Number |
The customer number is defined in the ACD queues for CallPilot. Consult the switch administrator to confirm the switch customer number. |
You must specify the following information for your T1/SMDI switch:
|
Item |
Description |
|
SMDI Transport Data Settings |
Enter the Poll timeout, Poll timeout threshold, Poll DN and MWI padding. |
|
COM Port Settings |
Enter the Port name, Port use type, Baud Rate, Parity, Number of data bits, Number of stop bits, and Flow control. |
You must specify the following information for your DSE switch:
|
Item |
Description |
|
Switch information |
Enter the MWI activation method, Set button, Clear button, MWI range, Maximum internal extension length, Voice bus type, Voice bus speed, and bus timing. |
If you purchased the Symposium Voice Services Support feature, you must
specify the following:
|
Item |
Description |
|
Symposium Call Center |
Enter the CLAN address of the Symposium Call Center Server. |
|
Class ID |
The Class ID column appears in the Channel Information table. For Access channels, enter the Class ID for the class of Symposium Call Center Server voice application that can be run on the channel. |
This section describes how to add or change channel information, or clear existing channel information.
The TNs that are programmed on the switch to support CallPilot must also be configured on CallPilot through this page for CallPilot to function properly. Any channels that are not configured on the switch and CallPilot cannot transfer calls between the switch and CallPilot.
On the left side of the page, click the link for
the set of channels that you want to configure.
The Channel Name column displays
the channels on the selected link.
Click the first channel that you want to configure in the Channel Name column. The Channel Detail Information page appears.
In the Channel
Detail Information page, enter values as described in the table
below:
To
save time, you can add a range of TNs instead of adding them one at a
time if the TNs are consecutively numbered on the switch for CallPilot.
Example
If you specify TN 1.0.0.0, and then specify 20 in the Number
of TNs box, a range of TNs from 1.0.0.0 to 1.0.0.19 is added to
the channel information table.
|
Box |
Description |
|
Number of TNs in |
Number of consecutive TNs in the range that you are configuring. You can only fill one DS30X link at one time (32 channels total). |
|
TNs |
The TNs programmed on the switch for CallPilot channels. |
|
Key 0 |
The Position ID of the agent for incoming call routing. Key 0 is defined for each TN on the switch. |
|
Key 1 |
The DN that represents channels for outgoing calls. Key 1 is defined for each TN on the switch. |
|
Class ID |
For Access channels, enter the Class ID for the class of Symposium Call Center Server voice application that can be run on the channel. |
|
Channel Allocation |
If you do not have the Symposium Voice Services Support feature installed, then choose Multimedia channel for all channels. Otherwise, choose one of the following channels from the drop-down menu in this box: Multimedia Channel - Choose this for voice, fax, or automated speech recognition channels. Access Channel - Choose this for channels that are dedicated to the Access ACD queue used for the Symposium Voice Services Support feature. IVR Channel - Choose this for channels that are dedicated to the IVR ACD queue used for the Symposium Voice Services Support feature. |
Click Fill, and then click OK to save the changes.
This procedure clears a range of TNs in the configuration information on the CallPilot server (TN is set to 0.0.0.0, and Key 0 and Key 1 are blank). This does not affect the TN programming on the switch.
On the left side of the page, click the link for the set of channels that you want to configure. The Channel Name column displays the channels on the selected link.
Click the first channel that you want to configure in the Channel Name column. The Channel Detail Information page appears.
In the Channel Detail Information page, enter the number of sequential TNs that you want to clear.
Click Reset. The TNs in the range you have specified are cleared (TN is set to 0.0.0.0, and Key 0 and Key 1 are blank).